 |
Adipic Acid SDS Safety Data Sheet of Supplier Exporter Manufacturers' Representative |
Email: info@ammol.org |
Call Toll Free +1-855-552-6665 |
Adipic Acid
CAS Number: 124-04-9
Molecular Formula: C6H10O4
Molecular Weight: 146.14
Adipic Acid
Adipic Acid SDS, Safety Data Sheet
MSDS Sheet, Material Safety Data Sheet 04-Feb-24
SECTION 1. PRODUCT IDENTIFICATION
Product Name & Other Names: Adipic Acid or Hexanedioic acid.
CAS Number: 124-04-9
EINECS EC Number: 204-673-3
Relevant uses and uses advised against (if any): Industrial Manufacturing.
Supplier: American Molecules, 9910 Bent Oak Dr, Houston, TX 77040, USA.
Call Toll Free: 1-855-55-AMMOL 1-855-552-6665.
In case of emergency contact: Will be given with the supply.
SECTION 2. HAZARDS IDENTIFICATION
GHS, Globally Harmonized System Classification in accordance with 29 CFR 1910
Classification according to Regulation (EC) No 1272/2008
Serious eye damage (Category 1)
Labeling according to GHS USA & Regulation (EC) No 1272/2008
GHS Label Elements Corrosive |
Signal Words: Danger
Hazard statements:
H318: Causes serious eye damage.
Precautionary statements:
P261: Avoid breathing dust/ fume/ gas/ mist/ vapors/ spray.
P262: Do not get in eyes, on skin, or on clothing.
P264 Wash skin thoroughly after handling.
P280: Wear protective gloves/protective clothing/eye protection/face protection.
P305+P351+P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
SECTION 3. COMPOSITION / INFORMATION ON INGREDIENTS
Product Identity: Adipic Acid or Hexanedioic acid.
CAS Number: 124-04-9
EINECS EC Number: 204-673-3
SECTION 4. FIRST AID MEASURES
Always seek medical attention after first aid measures are provided.
Eye Contact: Do not allow victim to rub eye (s). Let the eye (s) water naturally for a few minutes. If particle/dust does not dislodge, flush with lukewarm, gently flowing water for 5 minutes or until particle/dust is removed, while holding eyelid (s) open. If irritation persists, obtain medical attention. DO NOT attempt to manually remove anything stuck to the eye.
Skin Contact: Remove contaminated clothing, shoes and leather goods (e.g. watchbands, belts). Quickly and gently blot or brush away excess chemical. Wash gently and thoroughly with lukewarm gently flowing water and non-abrasive soap for 5 minutes. If irritation persists, repeat flushing. Obtain medical advice. Completely decontaminate clothing, shoes and leather goods before reuse or else discard.
Inhalation: If symptoms are experienced, remove source of contamination or move victim to fresh air. Obtain medical advice.
Ingestion: Never give anything by mouth if victim is rapidly losing consciousness or is unconscious or convulsing. Have victim rinse mouth thoroughly with water. DO NOT INDUCE VOMITING.
SECTION 5. FIRE FIGHTING MEASURES
Fire and Explosion Hazards: Not considered flammable but may burn at high temperatures. Airborne dusts of this product in an enclosed space and in the presence of an ignition source may constitute an explosion hazard.
Extinguishing Media: Use means of extinction appropriate for the surrounding fire conditions such as water spray, carbon dioxide, dry chemical, or foam.
Fire Fighting: Apart from oxides of carbon. toxic fumes may result from combustion. As with any fire, fire fighters should be fully trained and wear full protective clothing including an approved, self-contained breathing apparatus which supplies a positive air pressure within a full-face piece mask. Use water spray to cool unopened containers.
SECTION 6. ACCIDENTAL RELEASE MEASURES
Personal precautions, protective equipment and emergency procedures: Avoid breathing dust/fumes/gas/mist/vapors/spray. Use individual protective equipment (waterproof boots, suitable protective clothing, safety glasses, etc.). Restrict unprotected personnel from the area. Prevent any contact with hot surfaces. Do not approach facing the wind. Close-fitting safety goggles may be necessary in some circumstances to prevent eye contact.
Environmental precautions: Do not let the product enter drains, soil or water sources.
Methods and materials used for containment Cleanup procedures and Storage: Contain spilled material. Contain spill, isolate hazard area, and deny entry. Sweep up or vacuum. Place contaminated material in suitable, labeled containers for final disposal. Dispose of waste material consistent with the requirements of waste disposal authorities.
SECTION 7. HANDLING AND STORAGE
Precautions for safe handling: Apply according to good manufacturing and industrial hygiene practices. Ensure proper ventilation. Wash thoroughly after handling. Do not drink, eat or smoke while handling. Avoid contact with skin, eyes and clothing. Minimize dust generation. Avoid breathing dust/fumes/gas/mist/vapors/spray. Keep container tightly closed. Avoid ingestion and inhalation. Use individual protective equipment (waterproof boots, suitable protective clothing, safety glasses, etc.).
Conditions for safe storage, including any incompatibilities: Store in cool, dry and ventilated area away from heat sources and protected from sunlight in tightly closed original container. Keep air contact to a minimum. Do not leave the material container open. Store protected from heat, sparks and ignition sources and incompatible materials. Avoid contact with skin and eyes. Avoid inhalation of dust/mist/vapor. Do not store with incompatible materials like oxidizing agents, strong reducing agents and bases. Keep away from sources of ignition. Take measures to prevent the build-up of electrostatic charge. It is good practice to keep container closed when not in use. May form combustible dust concentrations in air. Use care during processing to minimize generation of dust. Good housekeeping is important to prevent accumulations of dust.
SECTION 8. EXPOSURE CONTROLS / PERSONAL PROTECTION
Protective Clothing: The hazard potential is low. Where there is large scale use of this material and significant potential for worker contact, gloves and long-sleeved work clothes or disposable coveralls may be necessary. Eye protection should be worn where dust is generated and there is a potential that eye contact may occur. Ensure that eyewash stations and safety showers are close to the workstation location. Do not breathe dust.
Ventilation: Use adequate local or general ventilation where necessary to maintain the concentrations of dust well below the recommended occupational exposure limits for general Particulates, Not Otherwise Specified (PNOS).
Respirators: Where dust or fumes are generated and cannot be controlled to within acceptable levels by engineering means, use appropriate NIOSH-approved respiratory protection equipment.
Exposure limit(s): Contains no substances with occupational exposure limit values in some countries. Better go by 5 mg/m3 TLV ACGIH.
SECTION 9. PHYSICAL AND CHEMICAL PROPERTIES
Appearance: It is a white, odorless granules crystals or powder
Odor: None
Odor threshold: Not applicable.
pH: 2.5 to 4
Relative density: 1.36
Freezing/Melting Point/Range: 151C to 154C
Boiling Point: Decomposes at 337C
Flash point: No data found.
Auto-ignition temperature: No data found.
Decomposition temperature: No data found.
Upper/lower flammability or explosive limits: No data found.
Vapor pressure: No data found.
Vapor density: No data found.
Evaporation rate: No data found.
Flammability (solid, gas): No data found.
Partition coefficient: n-octanol/water: No data found.
Solubility in Water: Soluble in water.
Viscosity: No data found.
SECTION 10. STABILITY AND REACTIVITY
Stability and Reactivity: Stable and not considered reactive under normal temperatures and pressures. Hazardous polymerization or runaway reactions will not occur.
Incompatibilities: Oxidizing agents. Avoid excessive heat, spark, flame, ignition dust formation and electrical charging. Also avoid strong reducing agents and bases.
Hazardous Decomposition Products: High temperature will generate carbon oxide and fumes.
SECTION 11. TOXICOLOGICAL INFORMATION
Acute Toxicity:
LD50 Oral - Rat - male and female - 5,560 mg/kg
LC0 Inhalation - Rat - male and female - 4 h - > 7.7 mg/l
LD0 Dermal - Rabbit - male and female - 7,940 mg/kg
Carcinogenicity: IARC: No component of this product present at levels greater than or equal to 0.1% is identified as probable, possible or confirmed human carcinogen by IARC.
Reproductive toxicity: No data found.
Teratogenicity: No data found.
Mutagenicity: No data found.
SECTION 12. ECOLOGICAL INFORMATION
Eco toxicological data:
Toxicity to fish: static test LC0 - Brachydanio rerio (zebrafish) - >= 1,000 mg/l - 96 h.
Toxicity to daphnia and other aquatic invertebrates: Immobilization LC50 - Daphnia magna (Water flea) - 46 mg/l - 48 h.
Mobility in soil: Soluble in water and hence likely to be mobile.
Persistence: Unlikely to persist due to water solubility.
Results of PBT and vPvB assessment: This substance/mixture contains no components considered to be either persistent, bioaccumulative and toxic (PBT), or very persistent and very bioaccumulative (vPvB) at levels of 0.1% or higher.
SECTION 13. DISPOSAL CONSIDERATIONS
Do not wash the material down drain. Put uncontaminated material back into the process if possible. Place contaminated material in suitable, labeled containers for disposal.
SECTION 14. TRANSPORT INFORMATION
Land Transport DOT USA, TDG Canada & ADR/RID Europe: Not dangerous goods.
Sea Transport IMO/IMDG: Not dangerous goods.
Air Transport ICAO/IATA: Not dangerous goods.
SECTION 15. REGULATORY INFORMATION
USA:
SARA 311/312 Hazards: See section 2.
California Prop. 65 Components: This product does not contain any chemicals known to State of California to cause cancer, birth defects, or any other reproductive harm.
SECTION 16 - ADDITIONAL INFORMATION
European Labeling in Accordance with EC Directives
H318: Causes serious eye damage.
DISCLAIMER: The information and recommendations set forth herein are presented in good faith and believed correct as of the date hereof. It is compiled from various sources, and it is not necessarily all inclusive nor fully adequate in every circumstance. In addition, these suggestions should not be confused with nor followed in violation of applicable laws, regulations, rules, or insurance requirements applicable. This SDS MSDS sheet is intended only as a guide to the appropriate precautionary handling of the material by a professionally trained person using this product. Individuals receiving the information must exercise their independent judgment in determining its appropriateness for a particular purpose. This shall not constitute a guarantee for any specific product features and shall not establish a legally valid contractual relationship. In no case shall our company be liable to loss or damages by the product user.
We also supply Adipic Acid of BP Ph Eur Grade.
Please visit Main Page of Adipic Acid Suppliers.
American Molecules, also known as ammol.org is a distributor, supplier and manufacturers' representative of all types of Pharmaceuticals, Functional Ingredients, Excipients and Specialty Chemicals in Texas USA. Our principals manufacture supply and export USP NF BP, Ph Eur, etc grades of chemicals pure and reagent grade, mineral fortifiers, FCC food grade. Tailor made particle size and customized specifications are offered. The principal's facility is having one or more of the certifications like FDA approval and GLP, cGMP, ISO9001, ISO14001, ISO/IEC 17025, ISO22000, FSSC 22000, ISO45001, FSSAI, Kosher, HALAL, COPP, WHO-GMP certified and Written Confirmation (WC) for export to Europe is available. The manufacturers suppliers and exporters observe WHO Good Manufacturing Practices and Good Laboratory Practices.
Suppliers and Manufacturers' Representative:
9910 Bent Oak Dr
Houston, TX 77040, USA
Call Toll Free: 1-855-55-AMMOL 1-855-552-6665
Email: info@ammol.org