 |
Aluminum Chloride Anhydrous SDS Safety Data Sheet of Supplier Exporter Manufacturers' Representative |
Email: info@ammol.org |
Call Toll Free +1-855-552-6665 |
Aluminum Chloride Anhydrous
CAS Number: Anhydrous 7446-70-0
Molecular Formula: AlCl3 Anhydrous
Molecular Weight: -134.34 Anhydrous
Aluminum Chloride Anhydrous
Aluminum Chloride Anhydrous SDS, Safety Data Sheet
MSDS Sheet, Material Safety Data Sheet 04-Feb-24
1. Product Identification
Product Name & Other Names: Aluminum Chloride Anhydrous or Aluminium Chloride Anhydrous or Aluminum trichloride or Trichloro aluminum.
CAS No.: 7746-70-0
EINECS: EC Number: 231-208-1
Relevant uses and uses advised against (if any): Industrial Manufacturing.
Supplier: American Molecules, 9910 Bent Oak Dr, Houston, TX 77040, USA.
Call Toll Free: 1-855-55-AMMOL 1-855-552-6665
In case of emergency contact: Will be given with the supply.
2. Hazards Identification
GHS, Globally Harmonized System Classification in accordance with 29 CFR 1910
Classification according to Regulation (EC) No 1272/2008:
Acute toxicity, oral Category 5
Skin corrosion/irritation Category 1A, B, C
Serious eye damage Category 1
Specific target organ toxicity – repeated exposure, Inhalation Category , Lungs.
Specific target organ toxicity – repeated exposure, Oral Category 2, Central nervous system.
Hazardous to the aquatic environment, acute hazard Category 3
Labeling according to GHS & Regulation (EC) No 1272/2008
GHS Label Elements  Health Hazard |
GHS Label Elements |
Signal Words: Danger
Hazard statements:
H303: May be harmful if swallowed.
H314: Causes severe skin burns and eye damage.
H372: Causes damage to organs (Lung, Central nervous system) through prolonged or repeated exposure.
H402: Harmful to aquatic life.
Precautionary statements:
P260: Do not breathe dust/fume/gas/mist/vapors/spray.
P261: Avoid breathing dust/ fume/ gas/ mist/ vapors/ spray.
P262: Do not get in eyes, on skin, or on clothing.
P270: Do not eat, drink or smoke when using this product.
P280: Wear protective gloves/protective clothing/eye protection/face protection.
P301 + P330 + P331 IF SWALLOWED: rinse mouth. Do NOT induce vomiting.
P303 + P361 + P352 IF ON SKIN (or hair): Remove/Take off immediately all contaminated clothing. Wash with plenty of soap and water.
P304 + P340 IF INHALED: Remove person to fresh air and keep comfortable for breathing.
P305+P351+P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
P314: Get Medical advice/attention if you feel unwell.
P337+P313: If eye irritation persists: Get medical advice/ attention.
Other hazards which do not result in classification: Reacts violently with water.
3. Composition/Information on Ingredients
Product Name & Other Names: Aluminum Chloride Anhydrous or Aluminium Chloride Anhydrous or Aluminum trichloride or Trichloro aluminum.
CAS No.: 7746-70-0
EINECS: EC Number: 231-208-1
4. First Aid Measures
Always seek medical attention after first aid measures are provided.
Inhalation: Remove to fresh air. If not breathing, give artificial respiration. If breathing is difficult, give oxygen. Get medical attention.
Ingestion: Never give anything by mouth to an unconscious person. Get medical attention.
Skin Contact: Wipe off excess material from skin then immediately flush skin with plenty of water for at least 15 minutes. Remove contaminated clothing and shoes. Get medical attention. Wash clothing before reuse. Thoroughly clean shoes before reuse.
Eye Contact: Immediately flush eyes with plenty of water for at least 15 minutes, lifting lower and upper eyelids occasionally. Get medical attention immediately.
Note to Physician: Treat symptomatically.
5. Fire Fighting Measures
Flammability of the Product: The product is not flammable.
Products of Combustion: It forms oxides of aluminum and hydrochloric acid when heated to decomposition.
Fire Extinguishing Media: Use dry chemical, foam, or carbon dioxide.
Special Information: In the event of a fire, wear full protective clothing and NIOSH-approved self-contained breathing apparatus with full face piece operated in the pressure demand or other positive pressure mode. At high temperatures or when moistened under fire conditions, it may produce toxic or irritating fumes.
6. Accidental Release Measures
Personal precautions, protective equipment, and emergency procedures: Ventilate area of leak or spill. Avoid breathing dust/fumes/gas/mist/vapors/spray. Use individual protective equipment (waterproof boots, suitable protective clothing, safety glasses, etc.). Restrict unprotected personnel from the area. Prevent any contact with hot surfaces. Do not approach facing the wind.
Environmental precautions: Do not let the product enter drains, soil, or water sources.
Methods and materials used for containment Cleanup procedures and Storage: Contain spilled material. Cover with an inert, non-combustible absorbent material, (e.g. sand, earth, diatomaceous earth, vermiculite). Vacuum or sweep-up and remove to an approved disposal container.
7. Handling and Storage
Precautions for safe handling: Apply according to good manufacturing and industrial hygiene practices. Ensure proper ventilation. In case of insufficient ventilation, wear suitable respiratory equipment. Wash thoroughly after handling. Do not drink, eat, or smoke while handling. Avoid contact with skin, eyes, and clothing. Minimize dust generation. Avoid breathing dust/fumes/gas/mist/vapors/spray. Keep container tightly closed. Avoid ingestion and inhalation. Use individual protective equipment (waterproof boots, suitable protective clothing, safety glasses, etc.).
Conditions for safe storage, including any incompatibilities: Store in cool, dry, and ventilated area away from heat sources and protected from sunlight in tightly closed original container. Keep air contact to a minimum. Store protected from heat, sparks and ignition sources and incompatible materials. Avoid contact with skin and eyes. Avoid inhalation of dust/mist/vapor. Do not store with incompatible materials like strong oxidizing agents, water, ethylene oxide, oxygen difluoride, phenols, nitro compounds, perchloryl fluoride, benzene. Avoid moisture and store away from water sources. It is to be stored in corrosive area.
8. Exposure Controls/Personal Protection
Airborne Exposure Limits: None established. Assure it as below 2mg/m3.
Ventilation System: A system of local and/or general exhaust is recommended to keep employee exposures as low as possible.
Personal Respirators (NIOSH Approved): For conditions of use where exposure to dust or mist is apparent and engineering controls are not feasible, a particulate respirator may be worn.
Skin Protection: Wear protective gloves and clean body-covering clothing.
Eye Protection: Use chemical safety goggles and/or full face shield where dusting or splashing of solutions is possible. Maintain eye wash fountain and quick-drench facilities in work area.
Other Control Measures: Maintain good housekeeping in work area. Handle in accordance with good industrial hygiene and safety practice. Wash hands after handling.
9. Physical and Chemical Properties
Appearance: Yellowish crystals or powder or granules.
Odor: Typical
Odor threshold: No data found.
pH: No data found.
Relative density: around 2.45
Boiling Point: Sublimes.
Melting Point: Sublimes.
Flash point: No data found.
Auto-ignition temperature: No data found.
Decomposition temperature: No data found.
Upper/lower flammability or explosive limits: No data found.
Vapor pressure: No data found.
Vapor density: No data found.
Evaporation rate: No data found.
Flammability (solid, gas): No data found.
Partition coefficient: n-octanol/water: No data found.
Solubility: Readily soluble in water and it reacts with it.
Viscosity: No data found.
10. Stability and Reactivity
Stability: Stable under ordinary conditions of use and storage. It must be kept in air-tight containers.
Hazardous Decomposition Products: It produces oxides of aluminum along with hydrochloric acid when heated to decomposition.
Hazardous Polymerization: Will not occur.
Incompatibilities: Reacts with metals and water including moisture. Water, ethylene oxide, oxygen difluoride, phenols, nitro compounds (organic, e.g. nitrobenzene, nitroglycerine, picric acid, trinitrotoluene), perchloryl fluoride, benzene are reported incompatibles.
Conditions to Avoid: Moisture, Heat, Sun light, Incompatibles.
11. Toxicological Information
Toxicity to Animals:
Skin, rabbit: LD50 = >2000 mg/kg;
Oral, mouse: LD50 = 1130 mg/kg;
Oral, rat: LD50 = 3450 mg/kg;
Carcinogenic Effects: Not a reported carcinogen.
Mutagenic Effects: It may have mutagenic effect.
Teratogenic Effects: No data found.
12. Ecological Information
Toxicity to fish:
LC50 - Carassius auratus (goldfish) - 0.15 mg/l - 7 d
LC50 - Oncorhynchus mykiss (rainbow trout) - 7 mg/l - 96 h
Toxicity to daphnia and other aquatic invertebrates:
EC50 - Daphnia magna (Water flea) - 3.9 mg/l - 48 h
Persistence and Degradability: No data found.
Mobility: No data found.
Bioaccumulation/ Accumulation: No data found.
Results of PBT and vPvB assessment: No data found.
13. Disposal Considerations
Whatever cannot be saved for recovery or recycling should be managed in an appropriate and approved waste disposal facility.
14. Transport Information
Land Transport DOT USA, TDG Canada & ADR/RID:
UN-Number: 1726 Class: 8 Corrosive Material Packing group: II
Proper shipping name: Aluminum Chloride Anhydrous
Marine pollutant: No
Poison Inhalation Hazard: No
Sea Transport IMO/IMDG:
UN-Number: 1726 Class: 8 Corrosive Material Packing group: II; -- EMS-No: F-A, S-Q
Proper shipping name: Aluminum Chloride Anhydrous
Marine pollutant: No
Air Transport ICAO/IATA
UN-Number: 1726 Class: 8 Corrosive Material Packing group: II
Proper shipping name: Aluminum Chloride Anhydrous
15. Regulatory Information
USA:
SARA 311/312 Hazards: See section 2.
California Prop 65: This product does not contain any chemicals known to State of California to cause cancer, birth defects, or any other reproductive harm.
16. Other Information
European Labeling in Accordance with EC Directives
H303 = May be harmful if swallowed.
H314 = Causes severe skin burns and eye damage.
H372 = Causes damage to organs (Lung, Central nervous system) through prolonged or repeated exposure.
H402 = Harmful to aquatic life.
DISCLAIMER: The information and recommendations set forth herein are presented in good faith and believed correct as of the date hereof. It is compiled from various sources, and it is not necessarily all inclusive nor fully adequate in every circumstance. In addition, these suggestions should not be confused with nor followed in violation of applicable laws, regulations, rules, or insurance requirements applicable. This SDS MSDS sheet is intended only as a guide to the appropriate precautionary handling of the material by a professionally trained person using this product. Individuals receiving the information must exercise their independent judgment in determining its appropriateness for a particular purpose. This shall not constitute a guarantee for any specific product features and shall not establish a legally valid contractual relationship. In no case shall our company be liable to loss or damages by the product user.
Please visit Main Page of Aluminum Chloride Hexahydrate Anhydrous Suppliers.
American Molecules, also known as ammol.org is a distributor, supplier and manufacturers' representative of all types of Pharmaceuticals, Functional Ingredients, Excipients and Specialty Chemicals in Texas USA. Our principals manufacture supply and export USP NF BP, Ph Eur, etc grades of chemicals pure and reagent grade, mineral fortifiers, FCC food grade. Tailor made particle size and customized specifications are offered. The principal's facility is having one or more of the certifications like FDA approval and GLP, cGMP, ISO9001, ISO14001, ISO/IEC 17025, ISO22000, FSSC 22000, ISO45001, FSSAI, Kosher, HALAL, COPP, WHO-GMP certified and Written Confirmation (WC) for export to Europe is available. The manufacturers suppliers and exporters observe WHO Good Manufacturing Practices and Good Laboratory Practices.
Suppliers and Manufacturers' Representative:
9910 Bent Oak Dr
Houston, TX 77040, USA
Call Toll Free: 1-855-55-AMMOL 1-855-552-6665
Email: info@ammol.org