 |
Antimony Pentachloride or Antimony Perchloride or Antimony(V) Chloride SDS Safety Data Sheet of Supplier Exporter Manufacturers' Representative |
Email: info@ammol.org |
Call Toll Free +1-855-552-6665 |
Antimony Pentachloride or Antimony Perchloride or Antimony(V) Chloride
CAS Number: 7647-18-9
Molecular Formula: SbCl5
Molecular Weight: 231-601-8
Antimony Pentachloride or Antimony Perchloride or Antimony(V) Chloride
Antimony Pentachloride SDS, Safety Data Sheet
MSDS Sheet, Material Safety Data Sheet 06-Feb-26
1. Product Identification
Product Name & Other Names: Antimony pentachloride or Antimony(V) chloride or Antimony perchloride.
CAS No.: 7647-18-9
EINECS EC Number: 231-601-8
Molecular Weight: 299.01
Molecular Formula: SbCl5
Relevant uses and uses advised against (if any): Industrial Manufacturing.
Supplier: American Molecules, 9910 Bent Oak Dr, Houston, TX 77040, USA.
Call Toll Free: 1-855-55-AMMOL 1-855-552-6665.
In case of emergency contact: Will be given with the supply.
2. Hazards Identification
GHS, Globally Harmonized System Classification in accordance with 29 CFR 1910
Classification according to Regulation (EC) No 1272/2008
Skin corrosion (Category 1A B C), H314
Chronic aquatic toxicity (Category 2), H411
Labeling according GHS & Regulation (EC) No 1272/2008
GHS Label Elements Corrosive | GHS Label Elements  Marine Pollutant |
Signal Word: Danger
Hazard Statements:
H314 Causes severe skin burns and eye damage.
H411 Toxic to aquatic life with long lasting effects.
Precautionary Statements - Prevention
P260: Do not breath dust/mist.
P264: Wash face, hands and any exposed skin thoroughly after handling
P271: Use only outdoors or in a well-ventilated area
P272: Contaminated work clothing should not be allowed out of the workplace.
P273 : Avoid release to the environment
P280: Wear protective gloves/ protective clothing/ eye protection/ face protection
P285: In case of inadequate ventilation wear respiratory protection
Precautionary Statements - Response
P302+P352: IF ON SKIN: Wash with plenty of water.
P304+P340: IF INHALED: Remove person to fresh air and keep comfortable for breathing
P305+P351+P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
P333+P313: If skin irritation or rash occurs: Get medical advice/ attention.
P337+P313: If eye irritation persists: Get medical advice/ attention
P342 + P311: If experiencing respiratory symptoms: Call a POISON CENTER or doctor.
P501: Dispose of contents/ container to an approved waste disposal plant.
3. Composition/Information on Ingredients
Product Name & Other Names: Antimony pentachloride or Antimony(V) chloride or Antimony perchloride.
CAS No.: 7647-18-9
EINECS EC Number: 231-601-8
4. First Aid Measures
Always seek medical attention after first aid measures are provided.
Inhalation: If inhaled, remove to fresh air. If breathing is difficult, give oxygen. Get medical attention.
Ingestion: Do not induce vomiting unless directed to do so by medical personnel. Never give anything by mouth to an unconscious person. If large quantities of this material are swallowed, call a physician immediately. Loosen tight clothing.
Skin Contact: Immediately flush skin with plenty of water for at least 15 minutes while removing contaminated clothing and shoes. Get medical attention. Wash clothing before reuse. Thoroughly clean shoes before reuse.
Eye Contact: Check for and remove any contact lenses. In case of contact, immediately flush eyes with plenty of water for at least 15 minutes. Get medical attention.
Notes to Physician: Treat symptomatically.
5. Fire Fighting Measures
Fire: It is not combustible, but substance is an oxidizer.
Fire Extinguishing Media: Alcohol-resistant foam, dry chemical, or carbon dioxide. Do not use a heavy water stream.
Special Information: Wear full protective clothing and breathing equipment for high-intensity fire or potential explosion conditions.
Special hazards arising from the substance or mixture: Hydrogen chloride gas, Chlorine and Antimony oxide with along with irritating fumes.
Special Information In the event of a fire, wear full protective clothing and NIOSH-approved self-contained breathing apparatus with full face piece operated in the pressure demand or other positive pressure mode. At high temperatures under fire conditions, it may produce toxic or irritating fumes.
6. Accidental Release Measures
Personal precautions, protective equipment, and emergency procedures: Avoid breathing dust/fumes/gas/mist/vapors/spray. Use individual protective equipment (waterproof boots, suitable protective clothing, safety glasses, etc.). Restrict unprotected personnel from the area. Prevent any contact with hot surfaces. Do not approach facing the wind. Do not touch the spilled material.
Environmental precautions: Do not let the product enter drains, soil, or water sources.
Methods and materials used for containment Cleanup procedures and Storage: Oxidizing material. Do not inhale dust, vapors, mist, or gas. Avoid dust formation. Contain spilled material. Cover with an inert, non-combustible absorbent material, (e.g. sand, earth, diatomaceous earth, vermiculite). Use a shovel to put the material into a convenient waste disposal container. Finish cleaning by spreading water on the contaminated surface and allow to evacuate as per law.
7. Handling and Storage
Precautions for safe handling: Apply according to good manufacturing and industrial hygiene practices. Ensure proper ventilation. In case of insufficient ventilation, wear suitable respiratory equipment. Wash thoroughly after handling. Do not drink, eat, or smoke while handling. Avoid contact with skin, eyes, and clothing. Minimize dust generation. Avoid breathing dust/fumes/gas/mist/vapors/spray. Avoid contact with eyes, skin, and clothing. Keep container tightly closed. Avoid ingestion and inhalation. Use individual protective equipment (waterproof boots, suitable protective clothing, safety glasses, etc.). Prevent any contact with hot surfaces.
Conditions for safe storage, including any incompatibilities: Store in cool, dry, and ventilated area away from heat sources and protected from sunlight in tightly closed original container. Keep air contact to a minimum. Store protected from heat, sparks and ignition sources and incompatible materials. Avoid contact with skin and eyes. Avoid inhalation of dust/mist/vapor. Do not store with incompatible materials like strong oxidizing agents, combustibles, organic or other readily oxidizable materials. Protect against physical damage and moisture. Isolate from any source of heat or ignition. Avoid storage on wood floors. Air sensitive.
8. Exposure Controls/Personal Protection
Airborne Exposure Limits: This product does not contain any hazardous materials with occupational exposure limits established by the region-specific regulatory bodies. Keep it under general guideline for Antimony compounds at 0.5 mg/m3.
Ventilation System: A system of local and/or general exhaust is recommended to keep employee exposures as low as possible. Local exhaust ventilation is generally preferred because it can control the emissions of the contaminant at its source, preventing dispersion in work area.
Respirators (NIOSH Approved): For conditions of use where exposure to dust or mist is apparent and engineering controls are not feasible, a particulate respirator (NIOSH type N95 or better filters) may be worn. If oil particles (e.g. lubricants, cutting fluids, glycerin, etc.) are present, use a NIOSH type R or P filter. For emergencies or instances where the exposure levels are not known, use a full-face positive-pressure, air-supplied respirator.
Protection: Wear impervious protective clothing, including boots, gloves, lab coat, apron or coveralls, as appropriate, to prevent skin contact.
Eye Protection: Use chemical safety goggles and/or full face shield where dusting or splashing of solutions is possible. Maintain eye wash fountain and quick-drench facilities in work area.
Other Control Measures: Maintain good housekeeping in work area. Dust deposits on floors and other surfaces may pick up moisture and cause the surfaces to become slippery and present safety hazards. Handle in accordance with good industrial hygiene and safety practice. Wash hands after handling.
9. Physical and Chemical Properties
p>Appearance: Colorless or yellow(fuming) liquid, oily.Odor: Pungent, offensive.
Odor threshold: Not available.
pH: around 6
Relative density: Not available.
Melting point/freezing point: 2.8C.
Initial boiling point and boiling range: 140C decomposes.
Flash point: Not available.
Auto-ignition temperature: Not available.
Decomposition temperature: Not available.
Upper/lower flammability or explosive limits: Not available.
Vapor pressure: Not available.
Vapor density: Not available.
Evaporation rate: Not available.
Flammability (solid, gas): Not available.
Partition coefficient: n-octanol/water: Not available.
Solubility(ies): Reacts with water. Soluble in alcohol, CHCl3, CS2,CCl4.
Viscosity: Not available.
Molecular Weight: 299.01
Molecular Formula: SbCl5.
10. Stability and Reactivity
Stability: It is stable under ordinary conditions of use and storage. Contact with water will generate hydrogen chloride. May be corrosive to metals. Reacts violently with water. May react with metals and lead to the formation of flammable hydrogen gas. Stable under normal conditions. Moisture sensitive.
Hazardous Decomposition Products: Hydrogen chloride gas, Chlorine and Antimony oxide, Fumes.
Hazardous Polymerization: Will not occur.
Incompatibilities: Bases, Strong oxidizing agents, Alcohols, Metals.
Conditions to Avoid: Incompatible products. Exposure to moist air or water. Heat, Flames, Ignition sources and incompatibles.
11. Toxicological Information
Oral rat LD50: 1115 mg/kg.
LC50 Inhalation: 720 mg/m³/2h (Rat)
Carcinogenic Effects: Not a reported carcinogen by NTP ACGIH OSHA.
Mutagenic Effects: No information available
Reproductive Effects: No information available.
Developmental Effects: No information available.
Teratogenicity: No information available.
12. Ecological Information
Environmental Fate: No information found.
Environmental Toxicity: Very toxic to aquatic life. Avoid release to the environment.
Persistence and Degradability: May persist.
Bioaccumulation/ Accumulation: No information available.
Mobility: Is not likely mobile in the environment.
13. Disposal Considerations
Whatever cannot be saved for recovery or recycling should be handled as hazardous waste and sent to a RCRA approved waste facility. Processing use or contamination of this product may change the waste management options. Dispose of container and unused contents in accordance legal requirements.
14. Transport Information
USA DOT, Canada TDG and ADR/RID Europe
Proper Shipping Name: ANTIMONY PENTACHLORIDE, LIQUID
Hazard Class: 8; Packing Group: II
UN/NA: UN1730
IATA & International (Air, I.C.A.O.)
Proper Shipping Name: ANTIMONY PENTACHLORIDE, LIQUID
Hazard Class: 8; Packing Group: II
UN/NA: UN1730
15. Regulatory Information
SARA 311/312: Acute Health Hazard
California Prop 65: California No Significant Risk Level: The product is not listed.
Section 16. Other Information
European Labeling in Accordance with EC Directives:
H314 Causes severe skin burns and eye damage.
H411 Toxic to aquatic life with long lasting effects.
Disclaimer:
**************************
Our company provides this MSDS sheet in good faith but makes no representation as to its comprehensiveness or accuracy. This SDS sheet is intended only as a guide to the appropriate precautionary handling of the material by a properly trained person using this product. The above information has been compiled from various sources and has the possibility of discrepancy and being out-dated information. Individuals receiving the information must exercise their independent judgment and do further search in determining its appropriateness for a particular purpose. In no case shall our company be liable to loss or damages by the product user.
**************************
American Molecules, also known as ammol.org is a distributor, supplier and manufacturers' representative of all types of Pharmaceuticals, Functional Ingredients, Excipients and Specialty Chemicals in Texas USA. Our principals manufacture supply and export USP NF BP, Ph Eur, etc grades of chemicals pure and reagent grade, mineral fortifiers, FCC food grade. Tailor made particle size and customized specifications are offered. The principal's facility is having one or more of the certifications like FDA approval and GLP, cGMP, ISO9001, ISO14001, ISO/IEC 17025, ISO22000, FSSC 22000, ISO45001, FSSAI, Kosher, HALAL, COPP, WHO-GMP certified and Written Confirmation (WC) for export to Europe is available. The manufacturers suppliers and exporters observe WHO Good Manufacturing Practices and Good Laboratory Practices.
Suppliers and Manufacturers' Representative:
9910 Bent Oak Dr
Houston, TX 77040, USA
Call Toll Free: 1-855-55-AMMOL 1-855-552-6665
Email: info@ammol.org