 |
Lithium Orotate Monohydrate or Orotic Acid Lithium Salt Monohydrate SDS Safety Data Sheet of Supplier Exporter Manufacturers' Representative |
Email: info@ammol.org |
Call Toll Free +1-855-552-6665 |
Lithium Orotate Monohydrate or Orotic Acid Lithium Salt Monohydrate
CAS Number: 5266-20-6
Molecular Formula: C5H3LiN2O4 Anhydrous and LiC5H3N2O4-H2O Monohydrate
Molecular Weight: 162.03 Anhydrous
Lithium Orotate Monohydrate or Orotic Acid Lithium Salt Monohydrate
Lithium Orotate Monohydrate or Orotic Acid Lithium Salt Monohydrate SDS, Safety Data Sheet
MSDS Sheet, Material Safety Data Sheet 25-Dec-24
SECTION 1 - IDENTIFICATION OF THE PRODUCT AND THE COMPANY
Product Name & Other Names: Lithium Orotate Monohydrate or Orotic Acid Lithium Salt Monohydrate
CAS No.: 5266-20-6
EINECS EC Number: 226-081-4
Relevant uses and uses advised against (if any): Industrial Manufacturing.
Suppliers: As per letterhead.
SECTION 2 - HAZARD IDENTIFICATION OF THE PREPARATION
GHS, Globally Harmonized System Classification in accordance with 29 CFR 1910
Classification according to Regulation (EC) No 1272/2008
Not a hazardous substance or mixture according to Regulation (EC) No. 1272/2008.
This substance is not classified as dangerous according to Directive 67/548/EEC.
Labeling according to GHS & Regulation (EC) No 1272/2008
GHS Label Elements NONE |
Signal Word: None
Precautionary statements:
P261: Avoid breathing dust/fume/gas/mist/vapors/spray.
P262: Do not get in eyes, on skin, or on clothing.
P281: Use personal protective equipment as required.
P302+P352: IF ON SKIN: Wash with plenty of soap and water.
P304+P340: IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing.
P305+P351+P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
P337+313: If eye irritation persists get medical advice/attention.
SECTION 3 - COMPOSITION/INFORMATION ON INGREDIENTS
Product Name & Other Names: Lithium Orotate Monohydrate or Orotic Acid Lithium Salt Monohydrate
CAS No.: 5266-20-6
EINECS EC Number: 226-081-4
SECTION 4 - FIRST-AID MEASURES
Skin: Immediately remove any contaminated clothing. Wash contaminated area thoroughly with soap and copious amounts of water for at least 15 minutes. If irritation or adverse symptoms develop, seek medical attention.
Eyes: Remove any contact lenses at once. Flush your eyes with water for at least 15 minutes. Ensure adequate flushing by separating the eyelids with fingers. If irritation or adverse symptoms develop, seek medical attention.
Ingestion: Contact a physician immediately.
Remove to fresh air, if coughing, breathing becomes labored, irritation develops or other symptoms develop, seek medical attention at once, even if Inhalation symptoms develop several hours after the exposure.
SECTION 5 - FIRE-FIGHTING MEASURES
Flammable Limits: Not established.
Hazardous Combustion Products: Carbon monoxide (CO), Carbon dioxide (CO2) and Lithium oxide.
Fire Extinguishing Media: Water spray, foam, carbon dioxide or dry chemical. No restriction on fire fighting media is prescribed.
Special Fire Fighting Procedures: Burning will produce toxic fumes. Firefighters should be equipped with SCBA with a full-face piece operated in the positive pressure demand mode with appropriate turnout gear and chemical resistant personal protective equipment. Fire-extinguishing work is done from the windward and a suitable fire-extinguishing method according to the surrounding situation is used.
Unusual Fire & Explosion Hazards: Concentrated dust may present an explosion hazard.
SECTION 6 - ACCIDENTAL RELEASE MEASURES
Personal precautions, protective equipment, and emergency procedures: Ventilate area of leak or spill. Avoid breathing dust/fumes/gas/mist/vapors/spray. Use individual protective equipment (waterproof boots, suitable protective clothing, safety glasses, etc.).
Environmental precautions: Do not let the product enter drains, soil, or water sources.
Methods and materials used for containment cleanup procedures and Storage: Contain spilled material. Cover with an inert, non-combustible absorbent material, (e.g., sand, earth, diatomaceous earth, vermiculite). Vacuum or sweep-up and remove to an approved disposal container. Clean up spills in a manner that does not disperse dust into the air.
SECTION 7 - HANDLING AND STORAGE
Precautions for safe handling: Apply according to good manufacturing and industrial hygiene practices. Avoid dust formation and control ignition sources. Employ grounding, venting and explosion relief provisions in accord with accepted engineering practices in any process of capable of generating dust and/or static electricity. Ensure proper ventilation. Wash thoroughly after handling. Do not drink, eat, or smoke while handling. Minimize dust generation. Avoid breathing dust/fumes/gas/mist/vapors/spray. Avoid contact with eyes, skin, and clothing. Keep container tightly closed. Avoid ingestion and inhalation. Use individual protective equipment (waterproof boots, suitable protective clothing, safety glasses, etc.).
Conditions for safe storage, including any incompatibilities: Store in cool, dry, and ventilated area away from heat sources and protected from sunlight in tightly closed original container. Keep air contact to a minimum. Store protected from heat, sparks and ignition sources and incompatible materials. Avoid inhalation of dust/mist/vapor. Do not store with incompatible materials like strong oxidizing agents and peroxides, strong mineral acids.
SECTION 8 - EXPOSURE CONTROL/PERSONAL PROTECTION
Exposure Guidelines: Not established by any regulatory body.
Respiratory Protection: Work ambient concentrations should be monitored and if airborne concentrations are expected to exceed acceptable levels wear a NIOSH/MSHA approved dust air purifying respirator.
Ventilation System: A system of local and/or general exhaust is recommended to keep employee exposures as low as possible.
Personal Respirators (NIOSH Approved): For conditions of use where exposure to dust or mist is apparent and engineering controls are not feasible, a particulate respirator may be worn.
Skin Protection: Wear protective gloves and clean body-covering clothing.
Eye Protection: Use chemical safety goggles and/or full-face shield where dusting or splashing of solutions is possible. Maintain eye wash fountain and quick-drench facilities in work area.
Other Control Measures: Maintain good housekeeping in work area. Handle in accordance with good industrial hygiene and safety practice.
SECTION 9 - PHYSICAL AND CHEMICAL PROPERTIES
Appearance: White to off-white crystalline powder.
Odor: No information found.
Odor threshold: No information found.
pH: No information found.
Relative density: No information found.
Melting point/freezing point: No information found.
Initial boiling point and boiling range: No information found.
Flash Point: No information found.
Auto-ignition temperature: No information found.
Decomposition temperature: No information found.
Upper/lower flammability or explosive limits: No information found.
Vapor pressure: No information found.
Vapor density: No information found.
Evaporation rate: No information found.
Flammability (solid, gas): No information found.
Partition coefficient: n-octanol/water: No information found.
Solubility(ies): No information found.
Viscosity: No information found.
SECTION 10 - STABILITY AND REACTIVITY
Incompatibility: Avoid contact with peroxides, strong mineral acids, and strong oxidizing agents.
Stability: Stable under ordinary conditions of use and storage.
Hazardous Decomposition Products: Carbon dioxide, carbon monoxide and lithium oxide.
Hazardous Polymerization: Will not occur.
SECTION 11 - TOXICOLOGICAL INFORMATION
Oral Rat LD50: No information found.
Carcinogenicity: No component of this product present at levels greater than or equal to 0.1% is identified as probable, possible, or confirmed human carcinogen by IARC.
Mutagenic Effects: No information found.
Teratogenic Effects: No information found.
Developmental Toxicity: No information found.
Reproductive Effects: No information found.
SECTION 12 - ECOLOGICAL INFORMATION
No significant data is available on the product. The product should be prevented from entering drains, sewers, streams, etc.
Persistence and Degradability: No information found.
Mobility: No information found.
Bioaccumulation/ Accumulation: No information found.
Results of PBT and vPvB assessment: No information found for assessment.
SECTION 13 - DISPOSAL CONSIDERATIONS
Prevent material from entering drains, sewers, streams, etc. Immediately dispose of waste material in accordance with federal, state, and local regulations.
SECTION 14 - TRANSPORT INFORMATION
DOT USA, TDG Canada & ADR/RID Europe: Not controlled.
IMO/IMDG: Not controlled.
IATA: Not controlled.
SECTION 15 - REGULATORY INFORMATION
USA Regulations:
California Proposition 65: Not listed for birth defects, reproductive harm and cancer.
Disclaimer:
**************************
Our company provides this MSDS sheet in good faith but makes no representation as to its comprehensiveness or accuracy. This SDS sheet is intended only as a guide to the appropriate precautionary handling of the material by a properly trained person using this product. The above information has been compiled from various sources and has the possibility of discrepancy and being out-dated information. Individuals receiving the information must exercise their independent judgment and do further search in determining its appropriateness for a particular purpose. In no case shall our company be liable to loss or damages by the product user.
**************************
American Molecules, also known as ammol.org is a distributor, supplier and manufacturers' representative of all types of Pharmaceuticals, Functional Ingredients, Excipients and Specialty Chemicals in Texas USA. Our principals manufacture supply and export USP NF BP, Ph Eur, etc grades of chemicals pure and reagent grade, mineral fortifiers, FCC food grade. Tailor made particle size and customized specifications are offered. The principal's facility is having one or more of the certifications like FDA approval and GLP, cGMP, ISO9001, ISO14001, ISO/IEC 17025, ISO22000, FSSC 22000, ISO45001, FSSAI, Kosher, HALAL, COPP, WHO-GMP certified and Written Confirmation (WC) for export to Europe is available. The manufacturers suppliers and exporters observe WHO Good Manufacturing Practices and Good Laboratory Practices.
Suppliers and Manufacturers' Representative:
9910 Bent Oak Dr
Houston, TX 77040, USA
Call Toll Free: 1-855-55-AMMOL 1-855-552-6665
Email: info@ammol.org