 |
Scale Inhibitor Liquid SDS Safety Data Sheet of Supplier Exporter Manufacturers' Representative |
Email: info@ammol.org |
Call Toll Free +1-855-552-6665 |
Liquid Scale Inhibitor
CAS Number: Mixture
Liquid Scale Inhibitor Fracturing
Slow release or Extended release Micro Encapsulated Solid Scale Inhibitor - ScaleFlush
CAS Number: Mixture
Slow release or Extended release Micro Encapsulated Solid Scale Inhibitor - ScaleFlush
Scale Inhibitor SDS, Safety Data Sheet
MSDS Sheet, Material Safety Data Sheet 13-Feb-26
1. Product Identification
Product Name/Synonyms: Scale Inhibitor
CAS No.: Mixture
Molecular Weight: It is a mixture
Recommended uses and uses advised against (if any): Oil & Gas Wells fracturing and Industrial Manufacturing.
Supplier: American Molecules, 9910 Bent Oak Dr, Houston, TX 77040, USA.
Call Toll Free: 1-855-55-AMMOL 1-855-552-6665.
In case of emergency contact: Will be given with the supply.
2. Hazards Identification
GHS, Globally Harmonized System Classification in accordance with 29 CFR 1910
Classification according to Regulation (EC) No 1272/2008
Acute toxicity, dermal Category 5, H313
Serious eye damage/eye irritation Category 2A, H319
Acute toxicity, inhalation Category 5, H333
Acute toxicity, oral Category 4, H302
Labeling according GHS USA & Regulation (EC) No 1272/2008
GHS Label Elements  Irritant |
Signal Words: Warning
Hazard statements:
H313: May be harmful in contact with skin.
H319: Causes serious eye irritation.
H333: May be harmful if inhaled.
H302: Harmful if swallowed.
Precautionary statements:
P262: Do not get in eyes, on skin, or on clothing.
P264: Do not eat, drink or smoke when using this product.
Wash skin thoroughly after handling.
P270 P280: Wear protective gloves/protective clothing/eye protection/face protection.
P312: Call a POISON CENTER or doctor/physician if you feel unwell.
P301+P312 : IF SWALLOWED: Call a POISON CENTER or doctor/physician if you feel unwell.
P304+P312: IF INHALED: Call a POISON CENTER or doctor/physician if you feel unwell.
P305+P351+P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
P330: Rinse mouth.
P337+P313: If eye irritation persists: Get medical advice/ attention.
P501: Dispose of contents/container to authorized people.
3. Composition/Information on Ingredients
Ingredient: Blend of Organophosphonates, Soda Ash, Water & Surfactants
CAS No.: Mixture
Composition/specific chemical identities of non-hazardous ingredients are withheld as a trade secret under the provisions of OSHA hazard communication standard 29 CFR 1910.1200
4. First Aid Measures
Always seek medical attention after first aid measures are provided.
Inhalation: Remove to fresh air. If not breathing, give artificial respiration. If breathing is difficult, give oxygen. Get medical attention.
Ingestion: Never give anything by mouth to an unconscious person. Get medical attention.
Skin Contact: Wipe off excess material from skin then immediately flush skin with plenty of water for at least 15 minutes. Remove contaminated clothing and shoes. Get medical attention. Wash clothing before reuse. Thoroughly clean shoes before reuse.
Eye Contact: Immediately flush eyes with plenty of water for at least 15 minutes, lifting lower and upper eyelids occasionally. Get medical attention immediately.
Note to Physician: Symptomatic and supportive treatment is recommended.
5. Fire Fighting Measures
Auto-Ignition Temperature: NA.
Flash Points: NA.
Explosion: Not considered to be an explosion hazard.
Fire Extinguishing Media: CO2, foam, dry chemicals.
Special Information: In the event of a fire, wear full protective clothing and NIOSH-approved self-contained breathing apparatus with full face piece operated in the pressure demand or other positive pressure mode. Containers can build up pressure if exposed to heat (fire). As in any fire, wear a self-contained breathing apparatus pressure-demand (MSHA/NIOSH approved or equivalent) and full protective gear. Apply alcohol-type foam or all-purpose foam manufacturers recommended techniques for large fires. Use carbon dioxide or dry chemical for small fires. Use water spray to keep containers cool.
6. Accidental Release Measures
Personal precautions, protective equipment, environmental precautions and emergency procedures: Avoid breathing dust/fumes/gas/mist/vapors/spray. Use individual protective equipment (waterproof boots, suitable protective clothing, safety glasses, etc). Restrict unprotected personnel from the area. Prevent any contact with hot surfaces. Do not approach facing the wind. Do not touch the spilled material. Keep away from drains, surface and groundwater and soil.
Methods and materials used for containment Cleanup procedures and Storage: Contain spilled material. Cover with an inert, non-combustible, inorganic absorbent material, or sweep up, and remove to an approved disposal container. Do not let the product enter drains. Sweep up and use a shovel to put the material into a convenient waste disposal container.
7. Handling and Storage
Precautions for safe handling: Apply according to good manufacturing and industrial hygiene practices with proper ventilation. Wash thoroughly after handling. Do not drink, eat, or smoke while handling. Avoid contact with skin, eyes, and clothing. Use with adequate ventilation. Minimize dust generation and accumulation. Avoid breathing dust/fumes/gas/mist/vapors/spray. Keep container tightly closed. Avoid ingestion and inhalation. Use individual protective equipment (waterproof boots, suitable protective clothing, safety glasses, etc). Prevent any contact with hot surfaces. Containers of this material may be hazardous when empty since they retain product residues.
Conditions for safe storage, including any incompatibilities: Store in cool, dry and ventilated area away from heat sources and protected from sunlight in tightly closed original container. Keep air contact to a minimum. Store protected from heat, sparks and ignition sources and incompatible materials. Avoid contact with skin and eyes. Avoid inhalation of dust/mist/vapor. Do not store with incompatible materials like strong acids, alkali, or oxidizing agents.
8. Exposure Controls/Personal Protection
Airborne Exposure Limits: None established.
Ventilation System: A system of local and/or general exhaust is recommended to keep employee exposures as low as possible. Local exhaust ventilation is generally preferred because it can control the emissions of the contaminant at its source, preventing dispersion of it into the general work area.
Personal Respirators (NIOSH Approved): For conditions of use where exposure to dust or mist is apparent and engineering controls are not feasible, a particulate respirator may be worn. For emergencies or instances where the exposure levels are not known, use a full-face positive-pressure, air-supplied respirator.
Skin Protection: Wear protective gloves and clean body-covering clothing.
Eye Protection: Use chemical safety goggles and/or full face shield where dusting or splashing of solutions is possible. Maintain eye wash fountain and quick-drench facilities in work area.
Other Control Measures: Maintain good housekeeping in work area. Dust deposits on floors and other surfaces may pick up moisture and cause the surfaces to become slippery and present safety hazards. Handle in accordance with good industrial hygiene and safety practice.
9. Physical and Chemical Properties
Appearance: Scale Inhibitor is light to yellow.
Odor: Characteristic.
Odor threshold: Not available.
pH: 5.0 - 10 at 10% solution at 25C (77F)
Relative density: 1.05 to 1.1
Boiling Point: > 212F
Melting Point: < 50F
Flash point: No data found.
Auto-ignition temperature: No data found.
Decomposition temperature: No data found.
Upper/lower flammability or explosive limits: No data found.
Vapor pressure: No data found.
Vapor density: No data found.
Evaporation rate: No data found.
Flammability (solid, gas): No data found.
Partition coefficient: n-octanol/water: No data found.
Solubility: It is soluble in water.
Viscosity: No data found.
10. Stability and Reactivity
Stability: It is stable under ordinary conditions of use and storage. Avoid contact with strong acids, alkali or oxidizing agents..
Hazardous Decomposition Products: It emits toxic fumes and carbon monoxide when heated to decomposition.
Hazardous Polymerization: Will not occur.
Incompatibilities: Avoid contact with strong acids, alkali or oxidizing agents.
11. Toxicological Information
Toxicity to Animals: LD50: No data found.
Carcinogenic Effects: No data found.
Teratogenic Effects: No data found.
Mutagenic Effects: No data found.
Developmental Toxicity: No data found.
Reproductive Effects: No data found.
12. Ecological Information
Toxicity to fish: No data found.
Persistence and Degradability: Unlikely to persist due to water solubility.
Mobility: Likely to be mobile due to water solubility.
Bioaccumulation/ Accumulation: Based on available information the product will not bio accumulate.
Results of PBT and vPvB assessment: No data found.
Environmental Toxicity: The material is not considered as environmental hazard.
13. Disposal Considerations
Whatever cannot be saved for recovery or recycling should be managed in an appropriate and approved waste disposal facility. State and local disposal regulations may differ from federal disposal regulations. Dispose of container and unused contents in accordance with law.
14. Transport Information
DOT USA, TDG Canada & ADR/RID Europe: Not Controlled.
IMDG/IMO: Not Controlled.
IATA: Not Controlled.
15. Regulatory Information
USA: SARA 313 Components: This material does not contain any chemical components with known CAS numbers that exceed the threshold reporting levels.
Section 16 - Additional Information
European Labeling in Accordance with EC Directives:
H313: May be harmful in contact with skin.
H319: Causes serious eye irritation.
H333: May be harmful if inhaled.
H302: Harmful if swallowed.
DISCLAIMER: The information and recommendations set forth herein are presented in good faith and believed correct as of the date hereof. It is compiled from various sources and it is not necessarily all inclusive nor fully adequate in every circumstance. In addition, these suggestions should not be confused with nor followed in violation of applicable laws, regulations, rules or insurance requirements applicable. This MSDS sheet is intended only as a guide to the appropriate precautionary handling of the material by a properly trained person using this product. Individuals receiving the information must exercise their independent judgment in determining its appropriateness for a particular purpose.
Please visit Main Page of Scale Inhibitor Suppliers.
American Molecules, also known as ammol.org is a distributor, supplier and manufacturers' representative of all types of Pharmaceuticals, Functional Ingredients, Excipients and Specialty Chemicals in Texas USA. Our principals manufacture supply and export USP NF BP, Ph Eur, etc grades of chemicals pure and reagent grade, mineral fortifiers, FCC food grade. Tailor made particle size and customized specifications are offered. The principal's facility is having one or more of the certifications like FDA approval and GLP, cGMP, ISO9001, ISO14001, ISO/IEC 17025, ISO22000, FSSC 22000, ISO45001, FSSAI, Kosher, HALAL, COPP, WHO-GMP certified and Written Confirmation (WC) for export to Europe is available. The manufacturers suppliers and exporters observe WHO Good Manufacturing Practices and Good Laboratory Practices.
Suppliers and Manufacturers' Representative:
9910 Bent Oak Dr
Houston, TX 77040, USA
Call Toll Free: 1-855-55-AMMOL 1-855-552-6665
Email: info@ammol.org