 |
Sodium Chloride USP Analytical Reagent Grade Supplier Exporter Manufacturers' Representative |
Email: info@ammol.org |
Call Toll Free +1-855-552-6665 |
Sodium Chloride
CAS Number: 7647-14-5
Molecular Formula: NaCl
Molecular Weight: 58.44
Sodium Chloride
Sodium Chloride SDS, Safety Data Sheet
MSDS Sheet, Material Safety Data Sheet 04-Feb-24
Section 1 - Chemical Product and Identification
Product Name & Other Names: Sodium Chloride or Common salt or Halite or Rock salt or Saline or Salt or Sea salt or Table salt.
CAS Number: 7647-14-5
EINECS EC Code: 231-598-3
Relevant uses and uses advised against (if any): Laboratory Chemicals and Industrial Manufacturing Use.
Supplier: American Molecules, 9910 Bent Oak Dr, Houston, TX 77040, USA.
Call Toll Free: 1-855-55-AMMOL 1-855-552-6665.
In case of emergency contact: Will be given with the supply.
Section 2 - Hazards Identification
GHS, Globally Harmonized System Classification in accordance with 29 CFR 1910
Classification according to Regulation (EC) No 1272/2008
Not a hazardous substance or mixture according to Regulation (EC) No. 1272/2008.
This substance is not classified as dangerous according to Directive 67/548/EEC.
Labeling according to GHS & Regulation (EC) No 1272/2008
GHS Label Elements NONE |
Signal Word: None
Precautionary statements:
P261: Avoid breathing dust/fume/gas/mist/vapors/spray.
P262: Do not get in eyes, on skin, or on clothing.
P281: Use personal protective equipment as required.
P302+P352 - IF ON SKIN: Wash with plenty of soap and water.
P304 + P340 - IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing.
P305 + P351 + P338 - IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
Section 3 - Composition, Information on Ingredients
Product Name & Other Names: Sodium Chloride or Common salt or Halite or Rock salt or Saline or Salt or Sea salt or Table salt.
CAS#: 7647-14-5
EINECS EC No.: 231-598-3
Section 4 - First Aid Measures
Always seek medical advice after the first aid treatment.
Eyes: Flush eyes with plenty of water for at least 15 minutes, occasionally lifting the upper and lower eyelids. Get medical aid.
Skin: Flush skin with plenty of soap and water for at least 15 minutes while removing contaminated clothing and shoes. Get medical aid if irritation develops or persists. Wash clothing before reuse.
Ingestion: If victim is conscious and alert, give 2-4 cupfuls of milk or water. Get medical aid. Wash mouth out with water.
Inhalation: Remove from exposure to fresh air immediately. If not breathing, give artificial respiration. If breathing is difficult, give oxygen. Get medical aid if cough or other symptoms appear.
Section 5 - Fire Fighting Measures
General Information: Water runoff can cause environmental damage. Dike and collect water used to fight fire. Wear appropriate protective clothing to prevent contact with skin and eyes. Wear a self-contained breathing apparatus (SCBA) to prevent contact with thermal decomposition products. Substance is noncombustible.
Extinguishing Media: For small fires, use water spray, dry chemical, carbon dioxide or chemical foam.
Special hazards arising from the substance: Hydrogen chloride gas, Sodium oxides.
Section 6 - Accidental Release Measures
Personal precautions, protective equipment, and emergency procedures: Avoid breathing dust/fumes/gas/mist/vapors/spray. Use individual protective equipment (waterproof boots, suitable protective clothing, safety glasses, etc.). Restrict unprotected personnel from the area. Prevent any contact with hot surfaces. Do not approach facing the wind.
Environmental precautions: Do not let the product enter drains, soil, or water sources.
Methods and materials used for containment Cleanup procedures and Storage: Do not inhale vapors, mist, or gas. Avoid dust formation. Contain spilled material. Cover with an inert, non-combustible absorbent material, (e.g. sand, earth, diatomaceous earth, vermiculite). Use a shovel to put the material into a convenient waste disposal container. Finish cleaning by spreading water on the contaminated surface and allow to evacuate as per law.
Section 7 - Handling and Storage
Precautions for safe handling: Apply according to good manufacturing and industrial hygiene practices. Ensure proper ventilation. In case of insufficient ventilation, wear suitable respiratory equipment. Wash thoroughly after handling. Do not drink, eat, or smoke while handling. Avoid contact with skin, eyes, and clothing. Minimize dust generation. Avoid breathing dust/fumes/gas/mist/vapors/spray. Keep container tightly closed. Avoid ingestion and inhalation. Use individual protective equipment (waterproof boots, suitable protective clothing, safety glasses, etc.).
Conditions for safe storage, including any incompatibilities: Store in cool, dry, and ventilated area away from heat sources and protected from sunlight in tightly closed original container. Keep air contact to a minimum. Store protected from heat, sparks and ignition sources and incompatible materials. Avoid contact with skin and eyes. Avoid inhalation of dust/mist/vapor. Do not store with incompatible materials like strong oxidizing agents, iron, or steel, building materials (such as cement), bromine, or trifluoride. Store protected from moisture.
Section 8 - Exposure Controls, Personal Protection
Engineering Controls: Good general ventilation should be sufficient to control airborne levels. Facilities storing or utilizing the material should be equipped with an eyewash facility and a safety shower.
Ventilation System: A system of local and/or general exhaust is recommended to keep employee exposures as low as possible.
Personal Respirators (NIOSH Approved): For conditions of use where exposure to dust or mist is apparent and engineering controls are not feasible, a particulate respirator may be worn.
Skin Protection: Wear protective gloves and clean body-covering clothing.
Eye Protection: Use chemical safety goggles and/or full face shield where dusting or splashing of solutions is possible. Maintain eye wash fountain and quick-drench facilities in work area.
Other Control Measures: Maintain good housekeeping in work area. Handle in accordance with good industrial hygiene and safety practice. Wash hands after handling.
Section 9 - Physical and Chemical Properties
Appearance: Solid. Colorless or white crystalline powder.
Odor: Odorless
Odor threshold: Not applicable.
pH: No data found.
Relative density: around 2.16
Boiling Point: 2575 deg F
Freezing/Melting Point:1474 deg F
Flash point: No data found.
Auto-ignition temperature: No data found.
Decomposition temperature: No data found.
Upper/lower flammability or explosive limits: No data found.
Vapor pressure: No data found.
Vapor density: No data found.
Evaporation rate: No data found.
Flammability (solid, gas): No data found.
Partition coefficient: n-octanol/water: No data found.
Solubility: Soluble in water.
Viscosity: No data found.
Section 10 - Stability and Reactivity
Chemical Stability: Stable.
Conditions to Avoid: High temperatures, exposure to moist air or water.
Incompatibilities with Other Materials: It reacts with most non-noble metals such as iron or steel, building materials (such as cement), bromine, or trifluoride. Potentially explosive reaction with dichloro-maleic anhydride + urea. Electrolysis of mixtures with nitrogen compounds may form explosive nitrogen tri-chloride.
Hazardous Decomposition Products: Toxic fumes of chlorine or hydrogen chloride and sodium oxide.
Hazardous Polymerization: Has not been reported.
Section 11 - Toxicological Information
LD50 Oral - Rat - 3,550 mg/kg (Sodium chloride)
LC50 Inhalation - Rat - 1 h - > 42,000 mg/m3 (Sodium chloride)
LD50 Dermal - Rabbit - > 10,000 mg/kg( Sodium chloride)
Carcinogenicity: No component of this product present at levels greater than or equal to 0.1% is identified as possible or confirmed human carcinogen by IARC, ACGIH, OSHA and NTP.
Teratogenic Effects: No data found.
Mutagenic Effects: No data found.
Developmental Toxicity: No data found.
Reproductive Effects: No data found.
Section 12 - Ecological Information
Toxicity to fish: LC50 - Lepomis macrochirus (Bluegill) - 5,840 mg/l - 96 h
Toxicity to daphnia and other aquatic invertebrates:
NOEC - Daphnia (water flea) - 1,500 mg/l - 7 d(Sodium chloride)
LC50 - Daphnia magna (Water flea) - 1,661 mg/l - 48 h(Sodium chloride)
Persistence and Degradability: Not likely to persist due to water solubility.
Mobility: Likely to be mobile due to water solubility.
Results of PBT and vPvB assessment: This substance/mixture contains no components considered to be either persistent, bioaccumulative and toxic (PBT), or very persistent and very bioaccumulative (vPvB) at levels of 0.1% or higher.
Section 13 - Disposal Considerations
Chemical waste generators must determine whether a discarded chemical is classified as a hazardous waste. US EPA guidelines for the classification determination are listed in 40 CFR Parts 261.3.
Section 14 - Transport Information
Land Transport DOT USA, TDG Canada & ADR/RID Europe: Not Regulated.
Sea Transport IMDG/IMO: Not Regulated.
Air Transport IATA/ICAO: Not Regulated.
Section 15 - Regulatory Information
USA:
SARA 311/312 Hazards: See section 2.
California Prop. 65 Components: This product does not contain any chemicals known to State of California to cause cancer, birth defects, or any other reproductive harm.
DISCLAIMER: The information and recommendations set forth herein are presented in good faith and believed correct as of the date hereof. It is compiled from various sources, and it is not necessarily all inclusive nor fully adequate in every circumstance. In addition, these suggestions should not be confused with nor followed in violation of applicable laws, regulations, rules, or insurance requirements applicable. This SDS MSDS sheet is intended only as a guide to the appropriate precautionary handling of the material by a professionally trained person using this product. Individuals receiving the information must exercise their independent judgment in determining its appropriateness for a particular purpose. This shall not constitute a guarantee for any specific product features and shall not establish a legally valid contractual relationship. In no case shall our company be liable to loss or damages by the product user.
Please visit Main Page of Sodium Chloride Suppliers.
American Molecules, also known as ammol.org is a distributor, supplier and manufacturers' representative of all types of Pharmaceuticals, Functional Ingredients, Excipients and Specialty Chemicals in Texas USA. Our principals manufacture supply and export USP NF BP, Ph Eur, etc grades of chemicals pure and reagent grade, mineral fortifiers, FCC food grade. Tailor made particle size and customized specifications are offered. The principal's facility is having one or more of the certifications like FDA approval and GLP, cGMP, ISO9001, ISO14001, ISO/IEC 17025, ISO22000, FSSC 22000, ISO45001, FSSAI, Kosher, HALAL, COPP, WHO-GMP certified and Written Confirmation (WC) for export to Europe is available. The manufacturers suppliers and exporters observe WHO Good Manufacturing Practices and Good Laboratory Practices.
Suppliers and Manufacturers' Representative:
9910 Bent Oak Dr
Houston, TX 77040, USA
Call Toll Free: 1-855-55-AMMOL 1-855-552-6665
Email: info@ammol.org