 |
Sodium Ethylparaben or Sodium Ethyl p-hydroxybenzoate SDS Safety Data Sheet of Supplier Exporter Manufacturers' Representative |
Email: info@ammol.org |
Call Toll Free +1-855-552-6665 |
Sodium Ethylparaben or Sodium Ethyl p-hydroxybenzoate
CAS Number: 35285-68-8
Molecular Formula: C9H10O3
Molecular Weight: 166.18
Sodium Ethylparaben or Sodium Ethyl p-hydroxybenzoate
Sodium Ethyl Paraben or Sodium Ethyl Hydroxybenzoate SDS, Safety Data Sheet
MSDS, Material Safety Data Sheet 04-Feb-24
SECTION 1. PRODUCT IDENTIFICATION
Product Name & Other Names: Sodium Ethylparaben, Sodium Ethyl Paraben or Sodium Ethyl Hydroxybenzoate.
CAS Number: 35285-68-8
EINECS EC Number: 252-487-6
Relevant uses and uses advised against (if any): Industrial Manufacturing.
Supplier: American Molecules, 9910 Bent Oak Dr, Houston, TX 77040, USA.
Call Toll Free: 1-855-55-AMMOL 1-855-552-6665.
In case of emergency contact: Will be given with the supply.
SECTION 2. HAZARDS IDENTIFICATION
GHS, Globally Harmonized System Classification in accordance with 29 CFR 1910
Classification according to Regulation (EC) No 1272/2008
Skin corrosion/irritation (Category 2), H315
Serious eye damage (Category 1), H318
Labeling according to GHS USA & Regulation (EC) No 1272/2008
GHS Label Elements |
Signal Words: Danger
Hazard statements:
H315: Causes skin irritation.
H318: Causes serious eye damage.
Precautionary statements:
P261: Avoid breathing dust/ fume/ gas/ mist/ vapors/ spray.
P262: Do not get in eyes, on skin, or on clothing.
P264 Wash skin thoroughly after handling.
P280: Wear protective gloves/protective clothing/eye protection/face protection.
P305+P351+P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
SECTION 3. COMPOSITION / INFORMATION ON INGREDIENTS
Product Name & Other Names: Sodium Ethylparaben, Sodium Ethyl Paraben or Sodium Ethyl Hydroxybenzoate.
CAS Number: 35285-68-8
EINECS EC Number: 252-487-6
SECTION 4. FIRST AID MEASURES
Always seek medical attention after first aid measures are provided.
Eye Contact: Do not allow victim to rub eye (s). Let the eye (s) water naturally for a few minutes. If particle/dust does not dislodge, flush with lukewarm, gently flowing water for 5 minutes or until particle/dust is removed, while holding eyelid (s) open. If irritation persists, obtain medical attention. DO NOT attempt to manually remove anything stuck to the eye.
Skin Contact: Remove contaminated clothing, shoes, and leather goods (e.g. watchbands, belts). Quickly and gently blot or brush away excess chemical. Wash gently and thoroughly with lukewarm gently flowing water and non-abrasive soap for 5 minutes. If irritation persists, repeat flushing. Obtain medical advice. Completely decontaminate clothing, shoes and leather goods before reuse or else discard.
Inhalation: If symptoms are experienced, remove source of contamination or move victim to fresh air. Obtain medical advice.
Ingestion: Never give anything by mouth if victim is rapidly losing consciousness or is unconscious or convulsing. Have victim rinse mouth thoroughly with water. DO NOT INDUCE VOMITING.
SECTION 5. FIRE FIGHTING MEASURES
Fire and Explosion Hazards: Not considered flammable but may burn at high temperatures.
Extinguishing Media: Use means of extinction appropriate for the surrounding fire conditions such as water spray, carbon dioxide, dry chemical, or foam.
Fire Fighting: Apart from oxides of carbon. toxic fumes may result from combustion. As with any fire, fire fighters should be fully trained and wear full protective clothing including an approved, self-contained breathing apparatus which supplies a positive air pressure within a full face-piece mask. Use water spray to cool unopened containers.
Special Information: In the event of a fire, wear full protective clothing and NIOSH-approved self-contained breathing apparatus with full face piece operated in the pressure demand or other positive pressure mode. At high temperatures under fire conditions, it may produce toxic or irritating fumes. Fire-extinguishing work is done from the windward and the suitable fire-extinguishing method according to the surrounding situation is used.
SECTION 6. ACCIDENTAL RELEASE MEASURES
Procedures for Cleanup: Stop release if possible, to do so safely. Contain spill, isolate hazard area, and deny entry. Sweep up or vacuum. Place contaminated material in suitable, labeled containers for final disposal. Dispose of waste material consistent with the requirements of waste disposal authorities.
Personal Precautions: Gloves and coveralls or other protective clothing are recommended for persons responding to an accidental release. Close-fitting safety goggles may be necessary in some circumstances to prevent eye contact.
Environmental Precautions: This Contamination of soil and water should be prevented. Keep spillage from entering soil, streams, or sewers.
SECTION 7. HANDLING AND STORAGE
Store in cool, dry, well-ventilated area away from incompatible substances. Protect from physical damage. Keep away from sources of ignition. Take measures to prevent the build-up of electrostatic charge. It is good practice to keep Sodium container closed when not in use. Avoid generating dust and the release of dust into the workplace. May form combustible dust concentrations in air. Use care during processing to minimize generation of dust. Good housekeeping is important to prevent accumulations of dust. Always practice good personal hygiene. Store at 15C to 25C.
SECTION 8. EXPOSURE CONTROLS / PERSONAL PROTECTION
Exposure Limits: This product does not contain any hazardous materials with occupational exposure limits established by the region-specific regulatory bodies.
Ventilation System: A system of local and/or general exhaust is recommended to keep employee exposures as low as possible.
Personal Respirators (NIOSH Approved): For conditions of use where exposure to dust or mist is apparent and engineering controls are not feasible, a particulate respirator may be worn.
Skin Protection: Wear protective gloves and clean body-covering clothing.
Eye Protection: Use chemical safety goggles and/or full face shield where dusting or splashing of solutions is possible. Maintain eye wash fountain and quick-drench facilities in work area.
Other Control Measures: Maintain good housekeeping in work area. Handle in accordance with good industrial hygiene and safety practice. Wash hands after handling.
SECTION 9. PHYSICAL AND CHEMICAL PROPERTIES
Appearance: It is a white, odorless granules or powder.
Odor: None
Odor threshold: Not applicable.
pH: 10 @ 1 gm/l
Relative density: No data found.
Freezing/Melting Point/Range: >115C
Boiling Point: 297C (Decomposes)
Flash point: No data found.
Auto-ignition temperature: No data found.
Decomposition temperature: No data found.
Upper/lower flammability or explosive limits: No data found.
Vapor pressure: No data found.
Vapor density: No data found.
Evaporation rate: No data found.
Flammability (solid, gas): No data found.
Partition coefficient: n-octanol/water: No data found.
Solubility in Water: Soluble in water.
Viscosity: No data found.
SECTION 10. STABILITY AND REACTIVITY
Stability and Reactivity: Stable and not considered reactive under normal temperatures and pressures. Hazardous polymerization or runaway reactions will not occur.
Incompatibilities: Oxidizing agents. Avoid excessive heat, spark, flame, ignition, and moisture.
Hazardous Decomposition Products: High temperature operations will generate carbon oxide and fumes.
SECTION 11. TOXICOLOGICAL INFORMATION
Acute Toxicity (Oral LD50): > 2,000 mg/kg Rat
Carcinogenicity: IARC: No component of this product present at levels greater than or equal to 0.1% is identified as probable, possible, or confirmed human carcinogen by IARC.
Teratogenic Effects: No data found.
Mutagenic Effects: No data found.
Developmental Toxicity: No data found.
Reproductive Effects: No data found.
SECTION 12. ECOLOGICAL INFORMATION
Eco toxicological data: No data available. May cause long lasting harmful effects to aquatic life.
Biodegradability: No information available.
Persistence and degradability: Expected to be biodegradable due to water solubility.
Mobility in soil: Expected to be mobile due to water solubility.
SECTION 13. DISPOSAL CONSIDERATIONS
Do not wash the material down drain. Put uncontaminated material back into the process if possible. Place contaminated material in suitable, labeled containers for disposal. Dispose of waste material consistent with the requirements of waste disposal authorities.
SECTION 14. TRANSPORT INFORMATION
Land Transport DOT USA, TDG Canada & ADR/RID Europe: Not Regulated.
Sea Transport IMDG/IMO: Not Regulated.
Air Transport IATA/ICAO: Not Regulated.
SECTION 15. REGULATORY INFORMATION
USA:
SARA 311/312 Hazards: See section 2.
California Prop. 65 Components: This product does not contain any chemicals known to State of California to cause cancer, birth defects, or any other reproductive harm.
SECTION 16 - ADDITIONAL INFORMATION
European Labeling in Accordance with EC Directives:
H315: Causes skin irritation.
H318: Causes serious eye damage.
DISCLAIMER: The information and recommendations set forth herein are presented in good faith and believed correct as of the date hereof. It is compiled from various sources, and it is not necessarily all inclusive nor fully adequate in every circumstance. In addition, these suggestions should not be confused with nor followed in violation of applicable laws, regulations, rules, or insurance requirements applicable. This SDS MSDS sheet is intended only as a guide to the appropriate precautionary handling of the material by a professionally trained person using this product. Individuals receiving the information must exercise their independent judgment in determining its appropriateness for a particular purpose. This shall not constitute a guarantee for any specific product features and shall not establish a legally valid contractual relationship. In no case shall our company be liable to loss or damages by the product user.
Please visit Main Page of Sodium Ethylparaben or Sodium Ethyl p-hydroxybenzoate Suppliers.
American Molecules, also known as ammol.org is a distributor, supplier and manufacturers' representative of all types of Pharmaceuticals, Functional Ingredients, Excipients and Specialty Chemicals in Texas USA. Our principals manufacture supply and export USP NF BP, Ph Eur, etc grades of chemicals pure and reagent grade, mineral fortifiers, FCC food grade. Tailor made particle size and customized specifications are offered. The principal's facility is having one or more of the certifications like FDA approval and GLP, cGMP, ISO9001, ISO14001, ISO/IEC 17025, ISO22000, FSSC 22000, ISO45001, FSSAI, Kosher, HALAL, COPP, WHO-GMP certified and Written Confirmation (WC) for export to Europe is available. The manufacturers suppliers and exporters observe WHO Good Manufacturing Practices and Good Laboratory Practices.
Suppliers and Manufacturers' Representative:
9910 Bent Oak Dr
Houston, TX 77040, USA
Call Toll Free: 1-855-55-AMMOL 1-855-552-6665
Email: info@ammol.org