 |
Tea Tree Oil EP BP Ph Eur Grade Supplier Exporter Manufacturers' Representative |
Email: info@ammol.org |
Call Toll Free +1-855-552-6665 |
Tea Tree Oil
CAS Number: 68647-73-4
Tea Tree Oil
Tea Tree Oil SDS, SAFETY DATA SHEET
MSDS SHEET, MATERIAL SAFETY DATA SHEET 14-Feb-26
1. PRODUCT AND COMPANY IDENTIFICATION
Product Name & Other Names: Tea Tree Oil.
CAS Number: 68647-73-4
FEMA: 3902
Relevant uses and uses advised against (if any): Industrial Manufacturing.
Supplier: American Molecules, 9910 Bent Oak Dr, Houston, TX 77040, USA.
Call Toll Free: 1-855-55-AMMOL 1-855-552-6665.
In case of emergency contact: Will be given with the supply.
2. HAZARDS IDENTIFICATION
GHS, Globally Harmonized System Classification in accordance with 29 CFR 1910
Classification according to Regulation (EC) No 1272/2008
Flammable liquids Category 4, H227
Acute toxicity, oral Category 4, H302
Acute toxicity, dermal Category 4, H315
Serious eye damage/eye irritation Category 2B, H319
Hazardous to the aquatic environment, acute hazard Category 3, H335
Labeling according to GHS & Regulation (EC) No 1272/2008
GHS Label Elements  Irritant |
Signal Words (GHS-USA): Warning
Hazard statements (GHS-USA):
H227: Combustible liquid.
H302: Harmful if swallowed.
H315: Causes skin irritation.
H319: Causes serious eye irritation.
H335: May cause respiratory irritation.
Precautionary statements (GHS-USA):
P210: Keep away from heat/sparks/open flames/hot surfaces – No smoking.
P264: Wash … thoroughly after handling.
P270: Do not eat, drink or smoke when using this product.
P273: Avoid release to the environment.
P280: Wear protective gloves/protective clothing/eye protection/face protection.
P312: Call a POISON CENTER or doctor/physician if you feel unwell.
P363: Wash contaminated clothing before reuse.
P301+312: IF SWALLOWED: Call a POISON CENTER or doctor/physician if you feel unwell.
P302+352: IF ON SKIN: Wash with soap and water.
P305+351+338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses if present and easy to do – continue rinsing.
P337+313: If eye irritation persists get medical advice/attention.
P370+378: In case of fire: Use CO2, foam, dry chemicals for extinction.
P403+235: Store in a well ventilated place. Keep cool.
P501: Dispose of contents/container to authorized agents only.
3. COMPOSITION / INFORMATION ON INGREDIENTS
Product Name & Other Names: Tea Tree Oil.
CAS Number: 68647-73-4
4. FIRST-AID MEASURES
Always seek medical advice after the first aid treatment.
Inhalation: If inhaled, remove to fresh air. If breathing is difficult, give oxygen. Get medical attention.
Ingestion: Give large amounts of water to drink. Never give anything by mouth to an unconscious person. Get medical attention.
Skin Contact: In case of contact, immediately flush skin with plenty of water. Cover the irritated skin with an emollient. Remove contaminated clothing and shoes. Cold water may be used. Wash clothing & Shoes before reuse. Get medical attention.
Eye Contact: Check for and remove any contact lenses. In case of contact, immediately flush eyes with plenty of water for at least 15 minutes. Cold water may be used. Get medical attention.
5. FIRE-FIGHTING MEASURES
Fire Extinguishing Media: Use water spray, alcohol-resistant foam, dry chemical or carbon dioxide. Use means suitable for extinguishing surrounding fire.
Non-recommended: Do not use direct water jet on burning material.
Extinguishing procedures: Closed containers may build up pressure at elevated temperatures. If possible, containers should be cooled with a water spray.
Special Information: In the event of a fire, wear full protective clothing and NIOSH-approved self-contained breathing apparatus with full face piece operated in the pressure demand or other positive pressure mode. At high temperatures under fire conditions, it may produce toxic or irritating fumes.
6. ACCIDENTAL RELEASE MEASURES
Personal precautions, protective equipment and emergency procedures: Avoid breathing dust/fumes/gas/mist/vapors/spray. Use individual protective equipment (waterproof boots, suitable protective clothing, safety glasses, etc.).
Environmental precautions: Do not let the product enter drains, soil or water sources.
Methods and materials used for containment Cleanup procedures and Storage: Contain spilled material. Cover with an inert, non-combustible absorbent material, (e.g. sand, earth, diatomaceous earth, vermiculite). Vacuum or sweep up, and remove to an approved disposal container. Avoid open flames or other sources of ignition. Keep air contact to a minimum.
7. HANDLING AND STORAGE
Precautions for safe handling: Apply according to good manufacturing and industrial hygiene practices. Ensure proper ventilation. Wash thoroughly after handling. Do not drink, eat or smoke while handling. Avoid contact with skin, eyes and clothing. Minimize dust generation. Avoid breathing dust/fumes/gas/mist/vapors/spray. Keep container tightly closed. Avoid ingestion and inhalation. Use individual protective equipment (waterproof boots, suitable protective clothing, safety glasses, etc.).
Conditions for safe storage, including any incompatibilities: Store in cool, dry and ventilated area away from heat sources and protected from sunlight in tightly closed original container. Keep air contact to a minimum. Do not leave the material container open. Store protected from heat, sparks and ignition sources and incompatible materials.Avoid inhalation of dust/mist/vapor. Do not store with incompatible materials like strong oxidizing agents, acids and alkalis. Containers may be hazardous when empty. Avoid open flames or other sources of ignition. Keep air contact to a minimum.
Fire protection: Keep away from ignition sources and naked flame.
8. EXPOSURE CONTROL
Exposure Limits: Not established by the region-specific regulatory bodies.
Respiratory Protection: Avoid to breath directly on the product. Apply local ventilations when appropriate.
Ventilation System: A system of local and/or general exhaust is recommended to keep employee exposures as low as possible. Local exhaust ventilation is generally preferred because it can control the emissions of the contaminant at its source, preventing dispersion of it into the general work area.
Personal Respirators (NIOSH Approved): For conditions of use where exposure to dust or mist is apparent and engineering controls are not feasible, a particulate respirator may be worn. For emergencies or instances where the exposure levels are not known, use a full-face positive-pressure, air-supplied respirator.
Skin Protection: Wear protective gloves and clean body-covering clothing.
Eye Protection: Use chemical safety goggles and/or full face shield where dusting or splashing of solutions is possible. Maintain eye wash fountain and quick-drench facilities in work area.
Other Control Measures: Maintain good housekeeping in work area. Dust deposits on floors and other surfaces may pick up moisture and cause the surfaces to become slippery and present safety hazards. Handle in accordance with good industrial hygiene and safety practice.
9. PHYSICAL AND CHEMICAL PROPERTIES
Appearance: Clear colorless to yellow liquid.
Odor: Typical.
Odor threshold: Not available.
pH: No data found.
Relative density: about 0.9
Melting point/freezing point: No data found.
Initial boiling point and boiling range: 165C.
Flash point: 64C.
Auto-ignition temperature: No data found.
Decomposition temperature: No data found.
Upper/lower flammability or explosive limits: No data found.
Vapor pressure: No data found.
Vapor density: No data found.
Evaporation rate: No data found.
Flammability (solid, gas): No data found.
Partition coefficient: n-octanol/water: No data found.
Solubility(ies): Insoluble in water.
Viscosity: No data found.
10. STABILITY AND REACTIVITY
Reactivity: It presents no significant reactivity hazards, by itself or in contact with water. Avoid contact with strong acids, alkali or oxidizing agents.
Decomposition: Carbon monoxide and unidentified organic compounds may be formed during combustion.
Hazardous Polymerization: Will not occur.
Conditions to Avoid: Heat, sparks, open flames and other ignition sources. Avoid temperatures exceeding the flash point. Contact with incompatible materials.
11. TOXICOLOGICAL INFORMATION
LD 50 ORAL/RAT (mg/Kg): 1900 mg/kg
LD 50 DERMAL/RABBIT (mg/Kg) 5000 mg/kg.
Carcinogenic Effects: Not a reported carcinogen by IARC, NTP, ACGIH, OSHA.
Mutagenic Effects: No data found.
Teratogenic Effects: No data found.
Developmental Toxicity: No data found.
12. ECOLOGICAL INFORMATION
Persistence and Degradability: No data found.
Mobility: No data found.
Bioaccumulation/ Accumulation: Biodegradable.
Results of PBT and vPvB assessment: No data available for assessment.
Precautions: Prevent contamination of soil, ground and surface water.
13. DISPOSAL CONSIDERATIONS
In accordance with local environmental laws. Avoid disposing into drainage systems and into the environment.
14. TRANSPORT REGULATIONS
DOT USA, TDG Canada & ADR/RID Europe:
UN Number: 1993
Class: 3
Packing Group: III
IMDG/IMO:
UN Number: 1993
Class: 3
Packing Group: III
IATA/ICAO:
UN Number: 1993
Class: 3
Packing Group: III
15. REGULATORY INFORMATION
USA:
SARA 311/312 Hazards: See section 2.
California Prop. 65 Components: Not listed.
Section 16 - Additional Information
European Labeling in Accordance with EC Directives:
H227: Combustible liquid.
H302: Harmful if swallowed.
H315: Causes skin irritation.
H319: Causes serious eye irritation.
H335: May cause respiratory irritation.
Disclaimer:
**************************
Our company provides this MSDS sheet in good faith but makes no representation as to its comprehensiveness or accuracy. This SDS sheet is intended only as a guide to the appropriate precautionary handling of the material by a properly trained person using this product. The above information has been compiled from various sources and has the possibility of discrepancy and being out-dated information. Individuals receiving the information must exercise their independent judgment and do further search in determining its appropriateness for a particular purpose. In no case shall our company be liable to loss or damages by the product user.
**************************
Please visit Main Page of Tea Tree Oil Suppliers.
American Molecules, also known as ammol.org is a distributor, supplier and manufacturers' representative of all types of Pharmaceuticals, Functional Ingredients, Excipients and Specialty Chemicals in Texas USA. Our principals manufacture supply and export USP NF BP, Ph Eur, etc grades of chemicals pure and reagent grade, mineral fortifiers, FCC food grade. Tailor made particle size and customized specifications are offered. The principal's facility is having one or more of the certifications like FDA approval and GLP, cGMP, ISO9001, ISO14001, ISO/IEC 17025, ISO22000, FSSC 22000, ISO45001, FSSAI, Kosher, HALAL, COPP, WHO-GMP certified and Written Confirmation (WC) for export to Europe is available. The manufacturers suppliers and exporters observe WHO Good Manufacturing Practices and Good Laboratory Practices.
Suppliers and Manufacturers' Representative:
9910 Bent Oak Dr
Houston, TX 77040, USA
Call Toll Free: 1-855-55-AMMOL 1-855-552-6665
Email: info@ammol.org