American Molecules - Ammol.org USA

Aluminum Sulfate Anhydrous Octadecahydrate USP Analytical Reagent FCC Food Grade Supplier Exporter Manufacturers' Representative

Call Toll Free +1-855-552-6665
Toll Free: 1-855-55-AMMOL

Quick Links to Products:

Aluminum ChlorideAluminum ChlorohydrateAluminum Monostearate and Aluminum DistearateAluminum Sulfate SuppliersDihydroxyaluminum AminoacetateDihydroxyaluminum Sodium Carbonate |  Dried Aluminum Phosphate |  Ammonium PersulfateCalcium Polystyrene SulfonateCalcium Sulfate  |  Ferric Sulfate or Iron III Sulfate  |   Ferrous Sulfate   |   Magnesium Aluminum SilicateMagnesium Sulfate  |   Micro Encapsulated Magnesium Sulfate  |  Potassium MonopersulfatePotassium Aluminum SulfateVanadyl SulfatePotassium Sulfate  |   Sodium Hydrogen Sulfate   |   Sodium Sulfate   |   Sodium Thiosulfate Pentahydrate Anhydrous   |   Tiemonium Methyl Sulfate  |  and more --

Aluminum Sulfate Anhydrous Octadecahydrate
CAS Number: Anhydrous 10043-01-3 and Octadecahydrate 7784-31-8

Molecular Formula: Al2(SO4)3 Anhydrous and Al2(SO4)3-18H2O Anhydrous
Molecular Weight: 342.14 Anhydrous and 666.43 Anhydrous.

Aluminum Sulfate Anhydrous Suppliers Aluminum Sulfate Octadecahydrate Suppliers
Aluminum Sulfate Anhydrous Octadecahydrate

Aluminum Sulfate USP Grade Specifications
Al2(SO4)3-xH2O (anhydrous) 342.15
Sulfuric acid, aluminum salt (3:2), hydrate.
Aluminum sulfate (2:3) hydrate
Anhydrous 342.16.

Aluminum Sulfate contains not less than 54.0 percent and not more than 59.0 percent of Al2(SO4)3. It contains a varying amount of water of crystallization.

Identification: A solution (1 in 10) responds to the tests for Aluminum and for Sulfate.
pH: not less than 2.9, in a solution (1 in 20).
Water: not less than 41.0% and not more than 46.0%.
Heavy metals: The limit is 20 µg per g.
Limit of alkalies and alkaline earths: To a boiling solution of 1.0 g in 150 mL of water add a few drops of methyl red TS and then add 6 N ammonium hydroxide just until the color of the solution changes to a distinct yellow. Add hot water to restore the volume to 150 mL, and filter while hot. Evaporate 75 mL of the filtrate to dryness, and ignite to constant weight: not more than 2 mg of residue remains (0.4%).
Limit of ammonium salts: Heat 1 g with 10 mL of 1 N sodium hydroxide on a steam bath for 1 minute: the odor of ammonia is not perceptible.
Iron: To 20 mL of a solution (1 in 150) add 0.3 mL of potassium ferrocyanide TS: no blue color is produced immediately.
Organic volatile impurities: meets the requirements.


Aluminum Sulfate FCC Food Grade Specifications
Al2(SO4)3 Formula weight, anhydrous 342.14
Al2(SO4)3-18H2O Formula weight, octadecahydrate 666.41
INS: 520 CAS: anhydrous 10043-01-3
CAS: octadecahydrate 7784-31-8

DESCRIPTION
Aluminum Sulfate occurs as a white powder, as shining plates, or as crystalline fragments. It is anhydrous or contains 18 molecules of water of crystallization. Because of efflorescence, the hydrate may have a composition approximating the formula Al2(SO4)3-14H2O. One gram of the hydrate dissolves in about 2 mL of water. The anhydrous approaches the same solubility, but the rate of solution is so slow that it initially appears to be relatively insoluble. The pH of a 1:20 aqueous solution is 2.9 or above.

REQUIREMENTS
Identification: A 1:10 aqueous solution gives positive tests for Aluminum and for Sulfate.
Assay Anhydrous: Not less than 99.5% of Al2(SO4)3, calculated on the ignited basis.
Octadecahydrate: Not less than 99.5% and not more than 114.0% of Al2(SO4)3-18H2O, corresponding to not more than approximately 101.7% of Al2(SO4)3-14H2O.
Alkalies and Alkaline Earths: Passes test (about 0.4%).
Ammonium Salts: Passes test.
Fluoride: Not more than 0.003%.
Lead: Not more than 3 mg/kg.
Loss on Ignition Anhydrous: Not more than 5%.
Note: This Requirement does not apply to Al2(SO4)3-18H2O.
Selenium: Not more than 0.003%.


Aluminum Sulfate Hydrated Analytical Reagent Grade Specifications
Al2(SO4)3-(14-18)H2O
CAS Number 7784-31-8 (for 18-hydrate)

REQUIREMENTS
Assay (as the labeled hydrate): 98.0-102.0%

MAXIMUM ALLOWABLE
Insoluble matter: 0.01%
Chloride (Cl): 0.005%
Substances not precipitated by ammonium hydroxide (as SO4): 0.2%
Heavy metals (as Pb): 0.001%
Iron (Fe): 0.002%.

We also supply Aluminum Sulfate of BP Ph Eur Grade.

Please visit SDS Safety Data Sheet of Aluminum Sulfate Suppliers.

American Molecules, also known as ammol.org is a distributor, supplier and manufacturers' representative of all types of Pharmaceuticals, Functional Ingredients, Excipients and Specialty Chemicals in Texas USA. Our principals manufacture supply and export USP NF BP, Ph Eur, etc grades of chemicals pure and reagent grade, mineral fortifiers, FCC food grade. Tailor made particle size and customized specifications are offered. The principal's facility is having one or more of the certifications like FDA approval and GLP, cGMP, ISO9001, ISO14001, ISO/IEC 17025, ISO22000, FSSC 22000, ISO45001, FSSAI, Kosher, HALAL, COPP, WHO-GMP certified and Written Confirmation (WC) for export to Europe is available. The manufacturers suppliers and exporters observe WHO Good Manufacturing Practices and Good Laboratory Practices.

Pallet Drums Bottles Pail Container

Suppliers and Manufacturers' Representative:
American Molecules - Ammol.org USA
9910 Bent Oak Dr
Houston, TX 77040, USA
Call Toll Free: 1-855-55-AMMOL 1-855-552-6665
Email: info@ammol.org